The right lighting in the workplace is not only important for health and well-being, but also a matter of safety.
Does your workplace have the right lighting conditions? In our FAQ, we give you some helpful tips to ensure you do not fumble in the dark when it comes to workplace lighting!
Inadequate lighting significantly increases the risk of accidents. In case of poor visibility, concentration and performance can also be reduced. Physical discomfort, such as burning eyes or headaches, not only affects well-being, but also has a negative impact on the frequency of errors in the work process.
Caution: Lighting that is too bright can also lead to problems when employees are blinded by unsuitable or misaligned lights.
Our infographic gives you a quick overview of the negative effects of wrong lighting in the workplace:
The employer is expected to set up workplaces in such a way that there are no health hazards for the employees. This also includes an adequate lighting for individual visual tasks.
Within the scope of a risk assessment, it is necessary to determine and regularly check whether the workstations are suitably lit during operation. This can be determined with a corresponding measuring device (luxmeter).
Daylight increases well-being but in practice it is not always sufficiently available at the right time or place. An additional artificial lighting system is therefore usually required. In our online shop you will find many lighting systems including wall and ceiling lights, tube lights, emergency lights and flashlights. Many products are also available in ex-protected design.
"The same light for all" is not an adequate solution in workplaces. Because it depends on the individual visual task, how much light is needed in the workplace. A general lighting system ensures a uniform illumination of the entire work area, but does not take into account the lighting requirements of individual room sections or workstations. Appendix 1 of the ASR A3.4 specifies the minimum values to be observed for the illuminances and color reproduction indices for the different areas.
Table: Recommended lighting levels:
Workspaces, jobs and activities | Lux Illuminance lx | Colour rendering index Ra |
---|---|---|
Traffic areas and corridors without vehicle traffic | 50 | 40 |
Traffic areas and corridors without vehicle traffic in the area of paragraphs and steps | 100 | 40 |
Traffic areas and corridors with vehicle traffic | 150 | 40 |
Shipping and packaging areas | 300 | 60 |
Storage rooms for identical or large-scale storage goods | 50 | 60 |
Storage rooms with search for non-identical storage | 100 | 60 |
Storage rooms with reading tasks | 200 | 60 |
Colour test, control | 1000 | 90 |
Laboratories, measuring stations | 500 | 80 |
Trimming, finishing, control work in the chemical, plastics and rubber industries | 750 | 80 |
Manufacture of tools and tools in metalworking and processing | 750 | 60 |
Surface treatment and varnishing in metalworking and processing | 750 | 80 |
Tool-, Gauging and device construction, precision and micromechanics in metalworking and processing | 1000 | 80 |
Painting: Repair, inspection in the automotive industry | 1000 | 90 |
Cable and wire production in the electrical industry | 300 | 80 |
Impregnation of coils, electroplating in the electrical industry | 300 | 80 |
Rough assembly work in the electrical industry, e.g. Large transformers | 300 | 80 |
Medium-size assembly work in the electrical industry, e.g. Switchboard | 500 | 80 |
Fine assembly work in the electrical industry, e.g. phones | 750 | 80 |
Very fine assembly work in the electrical industry, e.g. measuring instruments | 1000 | 80 |
Electronic workshops, testing, adjustment | 1500 | 80 |
Quality control in woodworking and processing | 1000 | 90 |
At no point in the area of the workplace may the temperature be 0.6 times lower than the average illuminance. The lowest value must not be within the range of the main vision task.
If minimum illuminance levels of more than 500 lux are stipulated, they do not necessarily have to be achieved at the entire workplace, but only at the partial surfaces relevant to the visual task. Partial lighting can be used, for example, when there is a special visual task (working with small parts, short observation periods) or when adaptation to the individual's vision of the employees is necessary. Here, for example, the use of additional workplace lighting is recommended.
The following infographic illustrates the different lighting requirements in a workshop:
It is advisable to plan and maintain lighting systems by a qualified person. After the installation of the lighting system and the necessary firing time, compliance with the legal requirements should be checked by means of control measurements.
Periodic testing and maintenance is also necessary to correct any changes in the lighting parameters, as well as to correct any contamination or damage.
In order to prevent glare, lighting should be selected to provide adequate visibility in work areas but operating conditions must also be considered. It may also be helpful to reduce differences in brightness between the glare source and the environment (for example due to bright ceilings and walls) as well as reflections due to matt surface design.
Lighting that offers a wide range of adjustment and positioning options are ideal here. In our online shop you will find practical models for installation in the office, on drawing tables or in workshops.
If your general lighting system fails, emergency lighting should already be installed to help avoid dangerous situations.
When planning and installing emergency lighting systems within your business, DIN EN 1838 and DIN EN 13032-3 should be observed.
Whether on the phone, via e-mail or in person at your premises - we are happy to help and advise you. Get in touch with us.
The specialist information on this page has been compiled carefully and to the best of our knowledge and belief. Nevertheless, DENIOS AG cannot assume any warranty or liability of any kind, whether in contract, tort or otherwise, for the topicality, completeness and correctness either towards the reader or towards third parties. The use of the information and content for your own or third party purposes is therefore at your own risk. In any case, please observe the locally and currently applicable legislation.
Give us a call or fill out the form and we will get back to you as soon as possible.
Calls are handled by our UK team. All sales are processed via our German parent company so are VAT* / tariff free where applicable. *Must be fully IE VAT registered
Use code DEN10 at checkout for 10% off ALL of our catalogue products. Cannot be combined with other promotions, discounts or other special prices. Does not apply to open quotations. IMPORTANT: our warehouse will close on the 17th of December, with the last date for dispatch being the 16th. It will reopen on the 2nd of January 2025.